HOME > PRODUCTS > SUNSEP-W > Specifications

COMMON SPECIFICATIONS

Use and Applicable Fluid: Dehumidification of Compressed Air
Fluid Temp. Range:[min. to max.]: -20 to +55°C (-4 to +131°F) Not freezed
Ambient Temp. Range:[min. to max.]: -20 to +55°C (-4 to +131°F) Not freezed
Pressure Range:[min. to max.]: Compressed Air Inlet to Outlet : 0 to 0.85MPa (0 to 120psig)
Purging Air Inlet to Outlet : 0 to 0.05MPa (0 to 7.1psig)

Applicable to dehumidification of other gases except air. Also, applicable to clean humidification of gases. please consult your distributor, if necessary.
To maintain satisfactory dehumidifying performance, we recommend use at a lower Fluid temp and within the range as follows.
| Fluid temp.-Ambient temp. | 5°C (9°F)

STANDARD SPECIFICATIONS

Model	Compressed Air Flow Rate L/min (scfm)	Dimensions mm (inch)	Connector Size		Weight kg (lbs)
Model	Compressed Air Flow Rate L/min (scfm)	Dimensions mm (inch)	Supply Air inlet / outlet	Purging Air inlet / outlet	Weight kg (lbs)
SWB-01-100	~150 ( ~5.3 )	Dia=32 (1.3),L=240 (9.4)	Rc1/4	Rc1/8	0.22 (0.49)
SWB-01-200	~100 ( ~3.5 )	Dia=32 (1.3),L=340 (13.4)	Rc1/4	Rc1/8	0.26 (0.57)
SWB-02-100	~300 ( ~10.6 )	Dia=50 (2.0),L=310 (12.2)	Rc3/8	Rc1/2	0.63 (1.34)
SWB-05-100	~600 ( ~21.2 )	Dia=50 (2.0),L=310 (12.2)	Rc3/8	Rc1/2	0.66 (1.46)
SWC-M04-70/IP	~ 30 ( ~1.1 )	W=36 (1.4),H=75 (3.0),D=15 (0.6)	M5 (Female)	M5 (Female)	0.05 (0.11)
SWC-M04-70/OP	~ 30 ( ~1.1 )	W=36 (1.4),H=75 (3.0),D=15 (0.6)	M5	-	0.05 (0.11)
SWC-M08-100	~ 70 ( ~2.5 )	W=61 (2.4),H=112 (4.4),D=31 (1.2)	Rc1/8	-	0.26 (0.57)
SWC-M15-100	~120 ( ~4.2 )	W=61 (2.4),H=112 (4.4),D=31 (1.2)	Rc1/8	-	0.27 (0.60)
SWC-01-150	~150 ( ~5.3 )	W=70 (2.8),H=150 (5.9),D=40 (1.6)	Rc1/4	-	0.39 (0.86)
SWC-02-250	~300 ( ~10.6 )	W=100 (3.9),H=200 (7.9),D=50 (2.0)	Rc3/8	-	0.69 (1.52)
SWC-03-250	~450 ( ~15.9 )	W=100 (3.9),H=200 (7.9),D=50 (2.0)	Rc3/8	-	0.71 (1.57)
SWF-M06-400	~ 30 ( ~1.1 )	Dia=25 (1.0),L=516 (20.3)	Rc1/4	Rc1/8	0.12 (0.26)
SWG-A01 series	~ 2 ( ~0.07 )	L=380~1890 (15~74.4)	1/4inch(6.35mm) <Taper shrink sealing connection>		0.03~0.095 (0.07~0.21)
SWG-035 series SWG-075 series	~10 ( ~0.35 ) ~20 ( ~0.71 )	L=714~1314 (28.1~51.7)	Rc1/4	Rc1/8	0.24~0.38 (0.53~0.84)

SWC-M04-70
A modified unit with a built-in purging orifice is also available upon request.
SWF-M06-400
Since the casing is constructed with a flexible material, the middle part of the casing can be bent into a U-shape with a minimum inside radius of curvature of 35mm(1.4inch), thus allowing installation in a narrow space.
SWG-A01 series
You can select from two materials, PP or PTFE
SWG-035,SWG-075 series
These are composed of only PP

SUNSEP-W_TM modules equipped with built-in purging circuits
Models SWC-01-150, SWC-02-250 and SWC-03-250 are equipped with built-in purging circuits with three (3) selective positions. Please refer to the following table.

Flow Rates of Purging Air (L/min(ANR)) [scfm]

Model	Position No.	Pressure (MPa) [psig]
Model	Position No.	0.7 [100]	0.5 [71]	0.3 [43]
SWC-01-150	1	6 [0.21]	5 [0.18]	3 [0.11]
	2	12 [0.42]	9 [0.32]	6 [0.21]
	3	25 [0.88]	19 [0.67]	12 [0.42]
SWC-02-250	1	25 [0.88]	19 [0.67]	12 [0.42]
	2	50 [1.77]	38 [1.34]	25 [0.88]
	3	75 [2.65]	56 [1.98]	37 [1.31]
SWC-03-250	1	50 [1.77]	38 [1.34]	25 [0.88]
	2	75 [2.65]	56 [1.98]	37 [1.31]
	3	125 [4.41]	94 [3.32]	63 [2.22]
SWC-M08-100	-	6 [0.21]	5 [0.18]	3 [0.11]
SWC-M15-100	-	12 [0.42]	9 [0.32]	6 [0.21]

| company profile | products | sitemap | japanese |