HOME > PRODUCTS > sunsepTM > Line-Up > Drying Compressed Gas SWB/SWC/SWF Series

sunsepTM
Drying Compressed Gas?SWB/SWC/SWF Series

SWB/SWC/SWF Series

メンブレン式ドライヤー　サンセップ(sunsep)

Standard Specifications (SWB/SWC/SWF Series)

Model
Supply　Air
Flow Rate
　L/min(ANR)
(scfm)
Dimensions
mm
（inch)
Connector Size
Weight

kgf
(lbs)
Purging
System
Supply
Gas
Inlet/Outlet
Purging
Gas
Inlet/Outlet
SWB-01-100
∼150
(∼5.3)
Dia=32
(1.3)
-
L=240
(9.4)
Rc1/4
(NPT1/4)
Rc1/8
(NPT1/8)
0.22
(0.49)
-
SWB-01-200
∼100
(∼3.5)
Dia=32
(1.3)
-
L=340
(13.4)
0.26
(0.57)
-
SWB-02-100
∼300
(∼10.6
Dia=50
(2.0)
-
L=310
(12.2)
Rc3/8
(NPT3/8)
Rc1/2
(NPT1/2)
0.63
(1.39)
-
SWB-05-100
∼600
(∼21.2)
0.66
(1.46)
-
SWB-10-150
∼1200
(∼42.4)
Dia=75
(3.0)
-
L=340
(13.4)
Rc1/2
(NPT1/2)
-
1.32
(2.91)
(*2)
SWB-17-200
∼1800
(∼63.6)
Dia=110
(4.3)
-
L=370
(14.6)
Rc1
(NPT1)
-
4.81
(10.6)
SWC-M04-70/OP
∼15
(∼0.5)
W=36
(1.4)
H=75
(3.0)
D=15
(0.6)
M5
(Female)
M5
(Female)
0.05
(0.11)
-
SWC-M04-70/IP
-
(*2)
SWC-M08-100
∼50
(∼1.8)
W=61
(2.4)
H=112
(4.4)
D=31
(1.2)
Rc1/8
(NPT1/8)
-
0.26
(0.58)
(*2)
SWC-M08-100/H
　(*1)
SWC-M15-100
∼80
(∼2.8)
W=61
(2.4)
H=112
(4.4)
D=31
(1.2)
Rc1/8
(NPT1/8)
-
0.27
(0.60)
(*2)
SWC-M15-100/H
　(*1)
SWC-01-150
∼150
(∼5.3)
W=70
(2.8)
H=150
(5.9)
D=40
(1.6)
Rc1/4
(NPT1/4)
-
0.39
(0.86)
(*2)
SWC-02-250
∼300
(∼10.6)
W=100
(3.9)
H=200
(7.9)
D=50
(2.0)
Rc3/8
(NPT3/8)
-
0.69
(1.53)
(*2)
SWC-03-250
∼450
(∼15.9)
W=100
(3.9)
H=200
(7.9)
D=50
(2.0)
Rc3/8
(NPT3/8)
-
0.71
(1.57)
(*2)
SWC-03-250/H
　(*1)
SWF-M06-400
　(*3)
∼30
(∼1.1)
Dia=25
(1.0)
-
L=516
(20.3)
Rc1/4
(NPT1/4)
Rc1/8
(NPT1/8)
0.12
(0.26)
-

(*1)These are the product of a low purge gas flow type.

(*2)These are equipped with built-in purging circuits, allowing ease of use without the purging line outside the unit.

(*3)Model : SWF-M06-400
Since the casing is constructed with a flexible material, the middle part of the casing can be bent into a U-shape with a minimum inner radius of curvature of 35mm(1.4 inch), thus allowing installation in a narrow space.

Common Specifications (SWB/SWC/SWF Series)

Use and
Applicable Fluid
Dehumidification of Compressed
Non-Corrosive Gas
Notes
Fluid Temp.
[min. ∼max.]
-4　∼　+131°F
(Not frozen)

-20　∼　+55℃
To maintain satisfactory dehumidifying performance, we recommend use at a lower Tin value and within the following range;
　|Tin-Tamb| ≤ 41°F

　|Tin-Tamb| ≤ 5°C
Ambient Temp
. [min. ∼max.]
-4　∼　+131°F
(Not frozen)

-20　∼　+55 °C
Pressure Range.
[min. ∼max.]
 Compressed Gas Inlet to Outlet　： 0∼0.85MPa( Gauge）　
Purging Gas Inlet to Outlet 　： 0∼0.05MPa(Gauge)

For Gas Analyzers

⇒【SWG Series Standard Specifications】

For　Medical Applications

⇒【SWT Series Specifications】

Flow Rate of Purging Gas（SWB/SWC series）
MPa （Gauge）
[psig]
Model
Switch
dial
Position
*2
0.3
[43］
0.5
［71］
0.7
［100］
Purging Air Flow Rate
No.
L/min
（ANR）
scfm
L/min
（ANR）
scfm
L/min
（ANR）
scfm
SWB-10-150 - 80 2.82 120 4.24 150 5.65
SWB-17-200 - 136 4.80 203 7.17 270 953
SWC-M04-70/IP - 1 0.04 1.5 0.05 2 0.07
SWC-M08-100 - 3 0.11 5 0.18 6 0.21
SWC-M08-100/H　*1　 - 1.5 0.05 2 0.07 3 0.11
SWC-M15-100 - 6 0.21 9 0.32 12 0.42
SWC-M15-100/H　*1 - 3 0.11 5 0.18 6 0.21
SWC-01-150 1 3 0.11 5 0.18 6 0.21
2 6 0.21 9 0.32 12 0.42
3 12 0.42 19 0.67 25 0.88
SWC-02-250 1 12 0.42 19 0.67 25 0.88
2 25 0.88 38 1.34 50 1.77
3 37 1.31 56 1.98 75 2.65
SWC-03-250 1 25 0.88 38 1.34 50 1.77
2 37 1.31 56 1.98 75 2.65
3 63 2.22 94 3.32 125 4.41
SWC-03-250/H　*1 1 12 0.42 19 0.67 25 0.88
2 25 0.88 38 1.34 50 1.77
3 37 1.31 56 1.98 75 2.65

*1 These product are low purge type.
*2 SWC-01-150、SWC-02-250、SWC-03-250、SWC-03-250/H　
　　　　　　 have Dial to control flow rate of Purging Gas.

AGC ENGINEERING CO.,LTD.

Technical Support

When specifications and on OEM contact are required, please feel free to consult with us.

North America

BELLEX INTERNATIONAL CORPORATION
200 Bellevue Parkway, Suite 180 Wilmington, DE 19809
Phone
+1-302-791-5180
Facsimile
+1-302-791-5190

China

GONG HUA TRADING(SHANGHAI) CO.,LTD.
ROOM 3407-3408, NAN ZHENG BUILDING, NO.580 NANJING ROAD(W), SHANGHAI, 200041 CHINA
Phone
+86-21-6267-2277
Facsimile
+86-21-6267-7277
E-Mail
louyy_gonghua@yahoo.co.jp

Japan and others

AGC Engineering Co., Ltd.
Customer Service Group.
Membrane System Div.
WBG MARIVE WEST 19F, 2-6-1 Nakase, Mihama-ku,
Chiba-shi, CHIBA 261-7119, JAPAN
Phone
+81-43-350-3378
Facsimile
+81-43-350-3383
E-mail
sunsep@agec.co.jp

Catalog

=>Download PDF File

Instructions for Use

  • To remove drainage, dust , etc. , we recommend that a filter (filtering capacity of　less than 5µm) be installed at the inlet line of supply gas. Dehumidifying efficiency may decrease if drainage is mixed into the inlet line. We therefore recommend that an automatic drain system be installed at the supply gas inlet.
  • When a sunsepTM unit is used for the line from a lubricating type compressor, we recommend that an automatic oil mist separator be installed at the inlet line of supply gas. The oil mist-separator must have an oil filterability capability of less than 0.3µm ( 95%　collection capability of dust diameter ) and should also have an oil-mist concentration of less than 1 mgf/Nm3.
  • Supply gas should be clean and free of dust, corrosive gas, organic solvent, and chemicals.
  • Excessive pressure should not be applied to the purging gas inlet and outlet.(max. 7.1psig)
  • For operation with a small amount of purging gas, not more than 0.35 scfm. we recommend that a small orifice be used instead of a needle valve.
  • When installing a pressure reducing valve, we recommend that the valve be installed at the outlet line of dry gas, which will increase dehumidifying efficiency.